BC458 DATASHEET PDF

BC Datasheet, BC PDF, BC Data sheet, BC manual, BC pdf, BC, datenblatt, Electronics BC, alldatasheet, free, datasheet, Datasheets, . ABSOLUTE MAXIMUM RATINGS. PARAMETER. SYMBOL. VALUE. UNIT. Collector-Base Voltage. VCBO. V. Collector-Emitter Voltage. VCEO. V. 2SC Transistor Datasheet pdf, 2SC Equivalent. Parameters and Characteristics.

Author: Mezilar Virn
Country: Cameroon
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 10 May 2005
Pages: 414
PDF File Size: 14.79 Mb
ePub File Size: 2.76 Mb
ISBN: 956-2-67525-957-5
Downloads: 42353
Price: Free* [*Free Regsitration Required]
Uploader: Meztit

Complete Technical Details can be found at the BC transistor datasheet give at the end of this page. Of the above types common emitter type is the popular and mostly used configuration.

BC Transistor Pinout, Equivalent, Working As Amplifier/Switch & Datasheet

The value of this resistor R B can be calculated using below formula. As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying the required amount of current to the base pin.

When this transistor is fully biased, it can allow a maximum of mA to flow across the collector and emitter. Interface SD Card with Arduino.

The input signal at base is amplified and taken at the emitter. Arduino based GPS receiver.

BC is a NPN transistor so the collector and emitter will be left open Reverse biased when the base pin is held at ground and will be closed Forward biased when a signal is provided to base pin. A Transistors acts as an Amplifier when operating in Active Region.

TOP Related  IN THE HANDS OF THE TALIBAN YVONNE RIDLEY PDF

In the absence of base signal, it gets completely off. Virgin Galactic — Commercial Space Flight. This is known as the biasing. SPI Module of Arduino. It is used for amplification and switching purposes. The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves. Choosing Motor For Robots.

For amplification applications, the transistor is biased such that it is partly on for all input conditions. Interface GPS with Arduino.

Transistor BC548

TL — Programmable Reference Voltage. Choosing Battery for Robots.

The maximum DC current gain is datashete Skip to main content. Anything more than 5mA will kill the Transistor; hence a resistor is always added in series with base pin to limit the current.

It can amplify power, voltage and current at different configurations.

These equivalent transistors however have different lead assignments. When used as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. The current gain may vary between and As mentioned the biasing current should be maximum of 5mA. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor.

TOP Related  JUVENILE HYALINE FIBROMATOSIS PDF

What is Web Browser.

BC Transistor Datasheet | Transistor BC PINOUT

When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. The voltage divider is the commonly used biasing mode. BC has a gain value of tothis value determines the amplification capacity of the transistor.

Its equivalent transistors are 2N and 2SC Submitted by admin on 16 March BC is general purpose silicon, NPN, bipolar junction transistor.

For switching applications, transistor is biased so that it remains fully on if there is a signal at its base. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. Amplifier modules like Audio amplifiers, signal Amplifier etc.

To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA. This high-density System-in-Package SiP integrates controller, power switches, and support components.

The variants of BC are A, B and C which vary in range of current gain and other characteristics. BC is used in common emitter configuration for amplifiers. The value of I B should not exceed 5mA.