The Boat Anchor Manual Archive Path: /hp/a/. This is the BAMA archive. These manuals are available for download and free of charge. I am now accepting. View and Download HP A operating and service manual online. DIGITAL VOLTMETER. A Measuring Instruments pdf manual download. Hp A Pdf User Manuals. View online or download Hp A Operating And Service Manual.

Author: Sasho Kagis
Country: Central African Republic
Language: English (Spanish)
Genre: Technology
Published (Last): 19 January 2008
Pages: 359
PDF File Size: 13.85 Mb
ePub File Size: 2.23 Mb
ISBN: 636-6-62068-991-6
Downloads: 85565
Price: Free* [*Free Regsitration Required]
Uploader: JoJokus

Example C is similar to A with the ex- ception that connecting guard in this manner allows any common-mode current generated between the source low and powerline ground to flow in the measurement circuit. In the Remote Operating mode, the 34SSA takes a certain amount of time to respond to a trigger message. Note the standoffs on the ASIC…. Connecting the Guard If a A input 345a5 greater than V is needed, the following procedure should always be followed.

Set the Decade Resistor to ohms. A terminal marked with this symbol must be connected to ground in the manner described in the installation opierating manual, and hpp operating the equipment.

The reading rate in the DC and Ohms mode will also increase when the High Resolution function is turned off. This test requires a calibrated decade resistor with settings that range from ohms to 10 megohms.

HP 3455A Manuals

Learn More – opens in a new window or tab Any international shipping and manuual charges are paid in part to Pitney Bowes Inc. Accurate 2 Wire Ohm Measurement: HP-IB Circuit Calibration module detail 2.

TOP Related  HTC LM2576 PDF

The A can be reset to the maximum rate by depressing the maximum button, after the display rate has been decreased. Included with this manual is an Operating information supplement.

The following options are majual for use with the Model 34S5A; Option Two-Wire Ohm Accuracy Test 4- Inguard-Outguard Connections 8-B-l. Get the item you ordered or get your money back.


The SA reading should be within the test limits listed in Tableverifying its 1-volt full scale accuracy with High Resolution on. If the mankal is less than three or four times more accurate than the DVM.

The A normally leaves the factory with the switch set to listen address 6 and talk address V decimal code However, the device must be HP-IB compatible. Repeat steps c through f to verify the 1 V and 10 V full-scale accuracy for negative readings. A kanual measurement is made for plied to the DC Preamp input through FET switch both gains and the results are stored by the main controller.

The SA display readings should be within the Test Limits given in the table. In order to bring the instrument out of this mode, any other function button must be pressed. Line Voltage Selection Items marked by a dagger t in the reference desig- Table Ordering Information Always downrange the Reference Divider before downranging the A.


HP A Digital Voltmeter Operaiting & SERVICE Manual | eBay

Simplified Output Circuit This trigger pulse 3455a to be ap- plied to the rear External Trigger Connector and should have a negative TTL edge and must be at least 3 seconds wide.

A MATH feature permits voltage or resistance measurements to be scaled into convenient units or to be- read directly in percent error from a selected reference. All major charrge information has been integrated into the manual by page revision. After the first measurement cycle is completed, the delayed trigger will iniate a second measurement cycle.

When trying to make an accurate 2 wire ohm measurement, the input lead resistance and the internal resistance of the A should be subtracted out from the reading. The talk and listen address is a 345a code which is selected to provide a unique address for each bus instrument.

Front and Rear Panel Features Hewlett-Packard further certifies that its calibration measurements are traceable to the United Slates Ha- lional Bureau of Standards, to the extent h by the Bureau ‘s calibration facility, and to the calibration facilities of other International Standards Organization members.